Internet access plan — Lot 1 Sheffield Road, Sheffield TAS 7306
8.2 ha bush block · container camp at −41.372605, 146.37865 (ground ~245.5 m) · desktop terrain study, 3 October 2026
· all geometry re-run from the true container point
The short answer. Check nbn fixed wireless first — it is free and takes 3 minutes
(your call, not ours: the nbn address checker is token-gated). If that comes back no: the working
setup is a 15 m mast at the SE tip of your block (“S1”), aimed ENE (~63°) at the
Sassafras towers — it clears both Telstra and Optus with full margin (0 dB, robust).
A 15 m mast at the container itself can only graze Deloraine (3.8 dB, ~27 km ESE) — that is the
fallback if a 230 m cable run or local solar is undesirable. Field-test before buying.
Three editions of this survey now exist. The owner should read this section if he read v2, because
some of v2’s headline conclusions no longer hold. None of them failed because the physics changed —
they failed because the measuring point was wrong.
v1 (the first report) had a genuine maths bug: a radian value was treated as degrees when stepping
longitude, so every terrain profile ran in roughly the wrong direction. Fixed.
v2 (the “revised report”) fixed the maths, but its anchor — the point all geometry
was measured from — was an OpenStreetMap road-node geocode ~1.1 km SSE of the container
(−41.38174, 146.38463; 1,132 m at bearing 153.8° from the true camp point). Its numbers
were internally consistent for that point. It just wasn’t your point. Worse, that anchor sat on
the far side of the container’s own south crest, so it “saw” over terrain that your container
cannot see over.
v3 (this report) re-runs every piece of geometry from the true container point
(−41.372605, 146.37865, ground 245.5 m), which was pinned down after v2 using your annotated map
(three independent readings agree within ~10 m). It also adds two things v2 never had: a
property-wide placement search (372 terrain cells, eight candidate spots S1–S8) and a
full 53-tower ranking.
The v2 claims that no longer hold
“There is exactly one clear path out of this site, and it is not a mobile tower:
nbn fixed wireless at Sheffield East, 1.7 km south-southwest, clear from ground level.”
— v2, “Bottom line”
v3: from the true container, that nbn tower (7306011) is 2.67 km away at 179° and is
blocked — you would need a ~118 m mast to get a ray-clear path. (The v2 anchor sat beyond
your own south crest; from there the path looked open.) The free nbn address check is still worth doing
— see §9 — but don’t bank on it.
“If nbn says no — a 45–60 m guyed mast aimed at 108° (ESE) for Elizabeth Town …
At 60 m you also gain clear sight of the Railton Optus/TPG site to the NE, so one mast could serve two carriers.”
— v2, “What actually works”
v3: from the container, Elizabeth Town (7304002) needs ~52.5 m for a bare ray and ~107.5 m for full
Fresnel — so even v2’s “60 m” was a graze, not a clean link. And Railton now needs
~127.5 m for even a bare ray — the “one mast, two carriers” idea is dead. Elizabeth
Town survives only as a long-shot engineered-mast option to quote later.
“Not in a tree, and not at 15 m any more.”
— v2, “Two things still worth correcting”
v3: half-reversed. “Not in a tree” still stands (§3). But “not at 15 m” was a
verdict for v2’s world — the container and its immediate surroundings. At the block’s SE tip (S1),
a spot outside v2’s scope, 15 m fully clears both Sassafras towers at 0 dB and is robust to
atmospheric bending. The 15 m plan comes back — at a new address.
Smaller corrections: the property is restated as Sheffield TAS 7306 (v2’s title said
Railton 7305); and the container bench ground is ~245.5 m on the survey DEM (v2 used 243 m at the geocode;
earlier documents said ~235 m AHD — the DEM value is what all v3 geometry uses).
Anchor sensitivity in numbers — same towers, three measuring points (click to expand)
nbn FW — Sheffield East (7306011)
Anchor
d km
brg°
clr@15 m
loss@15 dB
minMast LOS m
minMast F1 m
TRUE container (v3)
2.67
179.1
-66
33.1
118.0
132.0
v2 old anchor
1.72
195.5
6
0.0
7.5
13.5
provisional (listing geocode)
2.45
116.9
4
0.0
10.75
16.0
nbn FW — Sheffield town (7306012)
Anchor
d km
brg°
clr@15 m
loss@15 dB
minMast LOS m
minMast F1 m
TRUE container (v3)
4.32
249.2
-62
31.6
98.75
112.5
v2 old anchor
4.57
263.4
-94
38.4
167.25
187.75
provisional (listing geocode)
1.90
270.7
13
0.0
0.0
6.0
Optus — Sheffield (7306008)
Anchor
d km
brg°
clr@15 m
loss@15 dB
minMast LOS m
minMast F1 m
TRUE container (v3)
4.16
269.9
-97
30.9
186.0
233.5
v2 old anchor
4.77
282.2
-99
32.8
127.0
143.5
provisional (listing geocode)
2.55
307.6
15
0.0
0.0
17.5
Optus/TPG — Railton (7305003)
Anchor
d km
brg°
clr@15 m
loss@15 dB
minMast LOS m
minMast F1 m
TRUE container (v3)
4.39
55.6
-98
32.6
127.5
144.0
v2 old anchor
4.69
41.8
-24
16.8
58.25
99.25
provisional (listing geocode)
7.04
55.0
-129
31.4
251.75
302.0
Elizabeth Town (7304002)
Anchor
d km
brg°
clr@15 m
loss@15 dB
minMast LOS m
minMast F1 m
TRUE container (v3)
15.20
110.8
-32
17.1
52.5
107.5
v2 old anchor
14.39
107.8
-32
15.3
63.25
119.0
provisional (listing geocode)
16.79
103.3
-10
10.5
26.25
56.25
Clearance at a 15 m mast, straight rays, tower masts assumed 25 m AGL. Note how
7306011 flips from “clear from ground level” at the v2 anchor (+6 m clearance, 0.0 dB) to
“needs ~118 m of mast” from the true container — and how 7306008’s requirement jumps
from ~127 m to ~186 m. A ~1.1 km survey-point error changed which sites looked reachable at all. The
“provisional” anchor was the raw listing geocode used before the container was pinned; it is shown
only to demonstrate the instability.
What did not change: the bowl; the 1,225 m massif walling the west and south-west; the
western towers staying dead; the northwest walls; and the one iron rule of this whole study —
geometry is not signal. Every verdict below is a terrain calculation, not a measurement.
The field-test plan in §11 exists to convert one into the other.
2The short answer, in detail
1. Check nbn fixed wireless (free, 3 min)
Run the address through nbn.com.au/check. If Fixed Wireless is offered,
take it — nbn installs and aims the antenna, for free, and it’s the lowest-effort path.
Caveat: from the true container our geometry says the nearby nbn towers are
blocked (§9) — so expect a No, and treat a Yes as a pleasant surprise.
2. Best terrestrial setup: the S1 mast
15 m mast at S1 (SE tip; −41.374465, 146.379847; ground 249.4 m; ~230 m from the container).
Aim ~63° ENE. Clears Telstra 7307001 (12.52 km) and Optus 7307011 (12.67 km)
at 0 dB — full-Fresnel from 5.1 m of mast, so 15 m has ~10 m of margin. This is the strongest
result in the whole survey. Cost of the run: an extender/fibre, or local solar (§7, §8).
3. Simplest fallback: mast at the container
15 m mast at the camp itself, aimed 124.6° ESE at Deloraine (7304001, 27.4 km):
a grazing 3.8 dB straight-ray path (6.2 dB under standard atmospheric bending — marginal).
No 230 m cable, no new site. Good for voice/SMS-class service if the field test agrees; not a
“full engineering” link.
Test first, spend second. Everything above is geometry. The first weekend field test
(§11) costs ~A$100–300 and will tell you which of these is real at your camp,
with your handsets, in your weather. The single most expensive mistake this plan prevents is buying a mast
for the wrong spot — or buying anything at all before the free nbn check.
Your block, drawn to scale. Green line = boundary (PID 7673283); the container camp is
marked S8; the eight candidate mast spots S1–S8 with S1/S2 highlighted; the two signal corridors
(container→Deloraine ESE, and S1→Sassafras ENE) are drawn as arrows. Note the driveway: ~129 m of
private access from the north-east corner — S1 is on the far side of the block from the road.
Source: Crew 6 figure from placement.json (Crew 5) + property_dossier.json (Crew 1);
boundary and features from the LIST cadastre and survey notes; terrain from the z14 DEM.
3Your questions, answered
Can a 15 m tree-height setup work?
Yes — at S1. From the SE tip, a 15 m mast has both Sassafras towers fully clear at 0 dB
(Telstra 7307001: 24.9 m of clearance margin; Optus 7307011: 18.4 m), and the link stays clear even under
“k=4/3” atmospheric bending — the conservative case. Full Fresnel-zone clearance — the
comfort standard, not just a bare line — is reached from 5.1 m (Telstra) and 12.3 m (Optus)
of mast. At the container itself, 15 m gets you only the Deloraine graze (3.8 dB; marginal under k=4/3).
So the old “not at 15 m” verdict was about the container; at S1 the physics flip. (Why: S1 sits
beyond the crest that shadows the container, which is what opens the ENE corridor.)
Should the antenna go up a tree?
Not inside the canopy, and not on a tree as a permanent mount. Three reasons, all from the
solutions dossier: (1) a 15 m tree-top sways ±0.5–2 m in wind, and a ~10–11 dBi directional
panel loses most of its gain once it is more than a few degrees off-aim — sway becomes signal flicker;
(2) the tree grows into straps and re-sprouts through the path every season (you re-climb); (3) eucalyptus
canopy absorbs signal — ITU-R P.833 measured attenuation is ~0.17 dB/m at ~950 MHz in leaf, more when wet,
and dense evergreen canopy runs into tens of dB. The verdict stands: mount beside or above the canopy on a
rigid spar, pole or mast — or use the tree only for a low temporary field-test bracket, never for the
permanent install.
Do we need MIMO?
Yes — and it’s the easy kind to get. Every path worth having here is 700 MHz (Band 28) anchored,
and dual-polarised MIMO is exactly what helps a low-SINR, multipath-ish rural link: combining and
polarisation diversity buy several dB of effective improvement and fight the deep fades that make service
intermittent. One cross-polarised panel (e.g. Poynting XPOL-2-5G, 2×2, ~11 dBi class, A$305–380)
feeds both radio chains of the RUTX11/RUT241. The MikroTik ATL LTE18 kit goes further at 4×4. A
single-polarisation yagi is a 700-only specialist — you’d need two for MIMO.
Why do I get “one bar in certain spots”, and why do texts send late?
Because almost everything your phone hears is diffracted or scattered around the bowl —
not line-of-sight. The local walls (W 368 m @ 800 m, WNW 425 m @ 1000 m, N 371 m @ 1200 m, S 363 m @ 1000 m
from the camp notes) stand 6–10° above horizontal around the container; your phone only gets crumbs
over their edges. That lands you in the “marginal” band (~−113 dBm-class RSRP): the downlink
sometimes works, the uplink is the binding constraint (a handset transmits ~23 dBm against a tower’s far
larger budget), random-access retries ramp up, and small-packet sends stall on TCP’s ≥1 s minimum
retransmission timer — which is exactly what a “sent” SMS that arrives 30 s late looks like.
Wet foliage adds more loss; “one bar in certain spots” is a marginal multipath link doing its best.
Moving the antenna to S1 converts the link from diffraction-crumbs to a clean, aimed path.
Where is the best spot on the block?
S1 — the SE tip (−41.374465, 146.379847; ground 249.4 m; ~230 m from the container;
~3 m inside the fence line; ~7% slope for the mast base). Runner-up S2, ~40 m NE on the same ridge, but with a ~24%
slope that needs benching. Nothing else on the property clears the Sassafras pair. Whole-property search:
238 of 372 cells (64%) are clear-class at a 15 m mast — but most of those only via the Deloraine
corridor; 302 of 372 (81%) at 25 m. The west, north and Sheffield-side towers are blocked from every
cell on the block (masts of ~80–200 m would be needed — see §5).
4How signal reaches — and doesn’t reach — your camp
Three things dominate: a local bowl, a regional massif, and two openings.
The local bowl. Within ~1 km of the container the ground rises in almost every direction:
west ~368 m at 800 m, WNW ~425 m at 1000 m, north ~371 m at 1200 m, south ~363 m at 1000 m (per the camp
terrain notes). Measured at 15 m antenna height the horizon stands 2–10.5° above horizontal over
the western half of the compass; those sectors stay walled even at a 30 m mast.
The regional massif. The big one: the plateau peaks at 1,225 m, ~11 km SSW (221°)
— ~980 m above your bench. It is what kills every western and south-western tower, at any sane height.
The openings. The skyline is near-level in exactly two places: a shallow eastern window
(~80–95°) and the flattest one, ESE ~120–135° (horizon just 0.17–0.21° at 15 m).
And the block’s SE tip adds a second, better opening: standing ~230 m further out at the SE tip, the valley falls away toward the ENE, opening an aimed corridor to the Sassafras towers at ~63°.
Two corridors carry everything that is worth carrying:
Corridor A — from the container: ESE to Deloraine
Through the ~120–135° window: 7304001 Deloraine, 27.4 km at 124.6°. Terrain grazing
begins at ~3 m of mast; at 15 m the worst obstacle clears by +9.6 m and the knife-edge loss is 3.8 dB
(6.2 dB under k=4/3) — a real but thin path. Full Fresnel clearance needs 214 m — it is a
graze, not a full link. Secondary: 7304007 (Needles, 22.8 km at 144.9°, 6.1 dB) and the nbn
Dunorlan tower (10.7 dB). Everything else from the container is class D (blocked).
Corridor B — from S1: ENE to Sassafras
From the SE tip: 7307001 Telstra (12.52 km at 63.5°) and 7307011 Optus (12.67 km at
62.7°) — both fully clear at 0 dB from a 15 m mast, with 24.9 m / 18.4 m of clearance and
full Fresnel from 5.1 m / 12.3 m. This is the strongest path found anywhere on the block — and it does
not exist from the container.
The country around you, to ~54 × 39 km. The green pair (right) is the Sassafras
Telstra/Optus pair reached from S1; amber (lower right) is Deloraine reached from the container through the
ESE window (grazing at 15 m); grey dots are towers that are blocked. The green/amber rays are drawn only
where a 15 m mast at the marked spot genuinely clears. Sheffield and Railton towers (near you) are all
blocked from the container. Note: 29 of the 53 logged sites lie north of this window (Devonport–Latrobe–
Ulverstone) and are not shown.
Source: Crew 6 figure from towers.json (Crew 2), los_verdict.json/verdict_table.md
(Crew 5), placement.json (Crew 5), DEM AWS terrain z14.The sky, measured. Terrain elevation angle around the full compass from the TRUE
container point (20 km sweep, 5° bins, at +0/+15/+30 m antenna heights). Left: polar view — the
dent centred on the east-south-east is the only near-level window. Right: the same data linear —
only the NE–E–SE sector (roughly 60–150°) sits at or below ~1°. Everything from
200° through north back to 60° (west half) stays above 2–10.5° even at 30 m.
Source: Crew 5 horizon sweep, crew5/horizon_container.json; DEM AWS terrain z14.
Supersedes the v2-era provisional sweep from the wrong anchor.The one usable profile from the container: 27.4 km ESE to Deloraine (7304001).
Orange = 15 m mast ray; green = 30 m mast ray; the brown line is the terrain. The worst obstruction clears
by +9.6 m at 15 m (loss 3.8 dB) and +13.8 m at 30 m (loss 1.8 dB). Full Fresnel clearance would need a
214 m mast — hence “a graze”.
Source: Crew 6 profiles from Crew 5 data (site_7304001_from_container.png);
single knife-edge model, straight rays.
5Tower verdicts — every site that matters, ranked
All 53 sites within 30 km were profiled along true terrain from the container at a 15 m mast
(the owner’s tree-height case) and ranked by worst clearance. Classes at 15 m:
A · clear, full FresnelB · graze / ray-clear (≤6 dB)C · workable-marginal (6–12 dB)D · blocked (>12 dB).
Headline: from the container, exactly three sites are better than blocked at 15 m — and
only one of them is a commercial carrier you can install against: Deloraine (B, 3.8 dB, a graze).
Needles (C, 6.1 dB) and the nbn Dunorlan tower (C, 10.7 dB — informational) follow. Every other site,
including all the near ones (Sheffield, Railton, Sassafras pair), is D: blocked — the near towers
need masts of ~77–200 m for even a ray-clear path.
#
Site ID
Site
Carrier / band
d km
brg°
clr@15 m
loss@15 dB
loss k4/3 dB
class@15
minMast LOS m
minMast F1 m
1
7304001
36 Archer St DELORAINE TAS 7304
Optus 700MHz
27.41
124.6
10
3.8
6.2
B · graze
3.00
214.00
2
7304007
Off Mole Creek Road NEEDLES TAS 73
Optus 700MHz
22.82
144.9
-0
6.1
7.1
C · workable
15.25
44.75
3
7304008
Elizabeth Town 505 Dunorlan Road D
NBN 2300MHz
19.44
130.1
-9
10.7
12.9
C · workable
42.00
111.50
4
7304002
6413 Bass Highway Elizabeth Town T
Optus 700MHz
15.20
110.8
-32
17.1
17.5
D · blocked
52.50
107.50
5
7305002
Sunnyside South 698 Sunnyside Road
NBN 2300MHz
8.11
101.8
-40
24.6
24.8
D · blocked
85.75
148.25
6
7306002
OLIVERS RD MOUNT ROLAND TAS 7306
Telstra 700MHz
20.87
231.0
-46
20.6
21.0
D · blocked
65.75
95.25
7
7304016
Telstra 700MHz
28.69
126.4
-56
19.0
19.9
D · blocked
631.00
1181.25
8
7310022
Erriba 627 Cradle Mountain Road ER
Optus 700MHz
20.73
252.2
-56
24.4
24.6
D · blocked
74.75
97.00
9
7307001
Eversons Rd SASSAFRAS TAS 7307
Telstra 700MHz
12.52
64.6
-59
27.4
27.5
D · blocked
77.25
94.00
10
7307011
Optus 700MHz
12.66
63.7
-60
27.6
27.7
D · blocked
78.75
95.25
11
7306012
Sheffield 6 Spring Street SHEFFIEL
NBN 2300MHz
4.32
249.2
-62
31.6
31.6
D · blocked
98.75
112.50
12
7306011
Sheffield East 88 Bridle Track Roa
NBN 2300MHz
2.67
179.1
-66
33.1
33.2
D · blocked
118.00
132.00
Top 12 of 53 as ranked in verdict_table.md (§1). Clearance is
signed (positive = ray clears terrain); “minMast LOS” = mast height for a bare ray; “minMast F1” =
height for full first-Fresnel clearance. Beyond #12 come the rest — all class D — in the appendix below.
How the three best container paths behave with height. Top: worst clearance vs mast
height; bottom: knife-edge loss vs mast height, for the three least-blocked sites from the container.
Note how steeply Deloraine (orange) improves from ~0 m mast (clearance crosses zero at ~3 m) and how the
loss settles near 2 dB by 30 m; the other two need far more height.
Source: Crew 6 figure from Crew 5 data (clearance_loss_vs_mast_top3.png).
What a 15 m mast at the container actually achieves (the tree-height question)
Site ID
Site
clr@15 m
loss@15 dB
verdict@15
Comment
7304001
36 Archer St DELORAINE TAS 730
10
3.8
clear
ray clears / grazes — usable margin
7304007
Off Mole Creek Road NEEDLES TA
-0
6.1
blocked
partial-obstruction; workable-class
7304008
Elizabeth Town 505 Dunorlan Ro
-9
10.7
blocked
partial-obstruction; workable-class
7304002
6413 Bass Highway Elizabeth To
-32
17.1
blocked
blocked; needs ~35 m for ≤12 dB (exact)
7304016
-56
19.0
blocked
blocked; needs ~366 m for ≤12 dB (exact)
7307001
Eversons Rd SASSAFRAS TAS 7307
-59
27.4
blocked
blocked; needs ~69 m for ≤12 dB (exact)
7306012
Sheffield 6 Spring Street SHEF
-62
31.6
blocked
blocked; needs ~92 m for ≤12 dB (exact)
7306011
Sheffield East 88 Bridle Track
-66
33.1
blocked
blocked; needs ~111 m for ≤12 dB (exact)
7306008
5 Tarleton St SHEFFIELD TAS 73
-97
30.9
blocked
blocked; needs ~162 m for ≤12 dB (exact)
7305003
Railton 49A Foster Street RAIL
-98
32.6
blocked
blocked; needs ~119 m for ≤12 dB (exact)
7305001
151 Cement Works Road RAILTON
-102
32.7
blocked
blocked; needs ~160 m for ≤12 dB (exact)
7310021
Wilmot 2761 Wilmot Road WILMOT
-108
31.1
blocked
blocked; needs ~119 m for ≤12 dB (exact)
Full table: verdict_table.md §2. From the container a 15 m
mast yields exactly one carrier path — the Deloraine graze — plus two workable-marginal
informational receives. “Exact” mast needs in comments are analytic values beyond the 600 m scan cap.
Appendix: all 53 ranked sites, from the true container at a 15 m mast (click to expand)
Verbatim from verdict_table.md §1 (generated
2026-10-02T15:44Z, toolkit selftest PASS). “(>600)” = not achieved within the 600 m vertical scan
cap; “~X (>600)” = analytic value beyond the cap (physically real, not a viable mast).
Rows flagged “APPROX COORDS” use geocoded addresses rather than surveyed tower positions —
treat their numbers as indicative. nbn FW rows are informational (you can’t mount a subscriber antenna on
someone else’s tower; nbn installs its own).
6Where to put the mast: the eight candidates
Every non-road cell of the block was scored (372 cells) for best achievable mobile path at 15 m and 25 m.
Two sweet spots emerged, and they are different in kind:
238 / 372
cells clear-class (≤6 dB) at 15 m — mostly via Deloraine
302 / 372
cells clear-class at 25 m (81%)
64 / 302
extra cells that only clear when the mast goes from 15 to 25 m
S1 & S2
the only strip that clears the Sassafras pair
Spot
Where
Elev m
Best target(s) @15 m mast
Ray-LOS / full-F1 mast
Cable to container
Slope
Notes
S1
SE tip of the block, ~3 m inside the fence
249.4
Telstra 7307001 + Optus 7307011 (Sassafras pair) — 0 dB, both, k=4/3-robust; also Deloraine 5.3 dB
0 m (T) · 5.1 m (T, full-F1) / 12.3 m (O, full-F1)
~230 m
7%
BEST RF SPOT. ~24.9 m / 18.4 m clearance margin at 15 m. Keep a practical setback from the boundary; near-level bench.
S2
SE ridge, ~4 m inside the fence
246.2
Sassafras pair — 0 dB, both, k=4/3-robust
0 m (T) / 5.0 m (O); full-F1 15.5 / 21.0 m
~219 m
24%
Second-best RF; ~24% slope — needs benching/cut for a pad; 148 m from driveway.
S3
West boundary crest
270.2
Deloraine 7304001 only — 2.5 dB; Sassafras pair blocked by the mid-property ridge
0 m / 179 m
~332 m
52%
Impractical: ~52% slope, 1 m from boundary.
S4
West boundary crest
266.5
Deloraine only — 3.0 dB
0 m / 180 m
~340 m
52%
Impractical: ~52% slope.
S5
South bench, 133 m S of the container
259.7
Deloraine only — 3.9 dB (Needles 15.8 dB)
0 m / 189 m
~133 m
19%
Reaches only Deloraine; the south crest blocks the Sassafras pair.
S6
West crest, 0.4 m from the boundary
256.4
Deloraine only — 4.0 dB
0.8 m / 195 m
~309 m
51%
Impractical: ~51% slope.
S7
Close-in bench, 30 m SSE of the container
246.4
Deloraine — 4.0 dB (Needles 9.6 dB)
0.8 m / 213 m
~30 m
6%
Practical close-in cell; no Sassafras path (own crest in the way); 24 m from driveway.
S8 = container
As-built camp point (baseline)
245.5
Deloraine — 3.8 dB graze (6.2 dB under k=4/3); Needles 6.1 dB
2.8 m / 214 m
0 m
13%
What you have today: exactly one commercial path, and it is a graze — needs direct measurement.
Candidate data: placement.json (Crew 5) — 249.4 m at S1.
“Cable” is the straight-line distance to the container (~= minimum trench run; the real cable route is
longer and must be surveyed). Clearances/losses at 15 m from the same straight-ray, single-knife-edge model
as the tower tables. Slopes are local DEM values; >20% means benching/cut needed for a mast pad.
Why the spot matters: the same tower (Telstra’s Sassafras site, 7307001)
from the container vs from S1. From the container (left) the path to the Sassafras tower is buried
behind your own crest. From S1 (right) the crest is behind you and the ray clears with metres to spare.
Same tower, same 15 m mast, different address.
Source: Crew 6 figure from Crew 5 data
(compare_7307001_container_vs_spotS1.png).The whole-property search, 372 cells. Left: minimum mast height for a ray-clear path
(green = low mast needed). Right: best achievable mobile loss at a 25 m mast (green = strong path).
The two green corridors — the broad Deloraine corridor across the middle of the block, and the
S1/S2 strip at the SE tip — are the only places where a short mast works. Coordinates are metres
east/north of the container; the boundary polygon is to scale.
Source: Crew 6 label-fixed edition of Crew 5’s placement grid (placement.json);
no data changed.
Practical notes before you dig
Setback: S1’s best cells sit ~3 m inside the boundary. Keep a practical setback (say 5–10 m)
so the mast base, stays and guys are all on your land — the aim only needs the same bearing, and the
margins (18–25 m of clearance) swallow a few metres of setback comfortably.
The 230 m run: if the mast is at S1 you must either run ~230 m of cable (plus a PoE extender or
fibre), or power the mast locally with solar, or use the container fallback instead. Trade-off table in
§7 and options in §8.
Don’t trench until the field test says so (§11): test both S1 and the container bench with a
temporary pole first.
7Equipment & costs
Power-connection warning — read before buying any injector.
The Teltonika RUTX11/RUT241 routers are powered by passive PoE, Mode B (9–50 V / 9–30 V DC
respectively) — NOT 802.3af/at. A standard active PoE injector or PoE switch port can
damage them. The MikroTik ATL LTE18 kit is the opposite case: it expects proper
802.3af/at active PoE. Match the power source to the device — this is the single easiest
way to burn a router.
Item
Specific options
Indicative price (Oct 2026)
Notes
Router (lives at the mast)
Teltonika RUT241 (Cat 4)
A$299.20
Passive PoE 9–30 V; 2× SMA; economy baseline.
Router
Teltonika RUTX11 (Cat 6)
A$512.00
Passive PoE Mode B 9–50 V; the survey default; ≤16 W max.
Router
Teltonika RUT956
A$437.31
Industrial I/O — not needed here; listed for completeness.
Router + antenna, one box
MikroTik ATL LTE18 kit
A$631.87
Cat 18, 4×4 cross-pol panel built in; active PoE (af/at); no coax run; verify the AU band variant at purchase.
Antenna (recommended)
Poynting XPOL-2-5G (2×2 MIMO panel)
A$305–380
617–4200 MHz; up to 11 dBi; covers 700 MHz + higher — the cleanest single-panel MIMO choice for the RUT241/RUTX11.
Antenna (alternative)
RFI LPDA7038-11 log-periodic
A$220.00
Wideband directional, 11 dBi class.
Antenna (700 MHz specialist)
Powertec low-band yagi 13/14 dBi
A$317.40–330
Single-polarisation — two needed for MIMO; only if you commit to a 700-only path.
Cable
Gel-filled outdoor Cat6, 305 m reel
A$350.07 (≈A$1.15/m)
Ethernet home, not coax: keep the modem at the mast.
Cable (field kit)
Pre-terminated outdoor Cat6, 50 m
A$55.00
Test-rig convenience.
Surge / earth
Ubiquiti ETH-SP-G2 + earth rod + 6 mm² cable
A$28.51–31.36 + ≈A$16 + A$30–60 est.
Fit on every outdoor cable run.
Enclosure
Jaycar HB6134 sealed box (or larger IP66)
A$41.95 (larger A$60–150 est.)
At the mast, for router/injector.
Mast
6 m guyed lattice (retail example)
A$1,738.00
Ready-made option; a true 15 m class structure is quote-only in this study — treat mast lines as estimates.
PoE injection
Passive (TP-Link TL-POE2412G A$18.07; Ubiquiti POE-24-12W ≈A$29–40) / active for ATL kit
≈A$18–40
Passive vs active MUST match the router (see warning above).
Why no coax? RG-58-class cable loses ~11 dB per 25 m at 700 MHz. Over the 230 m
container→S1 run that is >100 dB — the signal would be gone before it arrived. That is why every
serious option here puts the modem at the mast and runs Ethernet (Cat6) or fibre back.
Scenario bundles
Scenario
Contains
Indicative total
1. Field-test rig (nothing committed)
Prepaid SIMs (2–3 carriers, ≈A$60–90) + 50 m Cat6 patch A$55 + bracket/straps A$50–150; borrow a pole/phone — or add a cheap pole.
A$100–300
2. S1-area 15 m-class build (if the field test says 15 m works)
RUT241 or RUTX11 A$299–512 + XPOL-2-5G A$305–380 + passive PoE A$18–40 + enclosure A$42–150 + Cat6 portion A$50–100 + surge/earth A$50–100 + solar A$600–1,150 + pole A$50–90.
≈A$1,450–2,550 + mast quote (15 m class) + the 230 m run choice below
3. Engineered mast long-shot (survey's 46–56 m class, mobile)
Mast + install + foundation A$1,000–1,800 (survey figure) + radio/antenna/cabling A$600–1,000 + solar A$600–1,150.
≈A$2,200–3,950 plus earthworks; get local quotes
4. nbn FW (if the address check says yes)
nbn installs the outdoor antenna + NTD; owner buys nothing.
A$0 hardware plan ≈A$60–86/mo
Bundle compositions from solutions.md (§3.5). The A$1,450–2,550 bundle assumes a
short DIY pole; a true 15 m engineered mast is quote-only (treat as estimate). The 230 m run choice:
(a) 230 m of Cat6 from the reel ≈A$265 plus a PoE extender or a fibre-converter pair
(estimate A$100–300 — not price-verified), or (b) power the mast locally with solar (already in bundle 2).
Choose (a) for no battery maintenance, (b) for zero trenching. Prices are indicative Oct 2026; see the
price-tier note in §13.
Before buying anything: the SIM question. Don't lock in a carrier or a modem band
variant until the field test (§11) says who wins at your camp. Every viable path here is
700 MHz (Band 28) anchored. If Telstra wins, a Boost SIM gives the full Telstra network at prepaid prices;
Optus/TPG paths need their own SIMs. Buy the winning carrier's SIM for the router afterwards.
8Power at the mast
If the mast is at S1 (~230 m from the container) there is no convenient mains. Either run power/data
along the fence line, or make the mast self-powered. Worked solar sizing (Launceston insolation basis):
288 Wh/day
design load (12 W continuous router + Wi-Fi)
≈320 Wh/day
drawn from the battery (+10% conversion)
5.4 MJ/m²/day
June mean solar exposure, Launceston (BOM) — the binding month
300 W panel
needed ≥229 W → choose 300 W for cloudy-sequence margin (≈A$150–250)
Panel: 300 W rigid mono/TOPCon (≈A$150–250 indicative). June plane-of-array ≈2.0
kWh/m²/day (tilt +30–40% winter gain — estimate; BOM figures are measured).
Battery: 3 days autonomy = 960 Wh → 100 Ah class LiFePO4 (budget ≈A$250–450 est.;
Renogy 100 Ah Pro self-heating A$645.50–707).
MPPT: Victron SmartSolar 100/20 A$130–136 (step to 100/30 A$170 for a full 300 W). Skip PWM
controllers — they waste 10–30% of the array.
Cold-charge warning. LiFePO4 must not be charged below 0°C, and an
unheated box in a Tasmanian winter reaches that. Fit a low-temperature charge cut-off (many BMS units have
one), insulate the enclosure, or buy the self-heating battery model.
Marginal-weather reality: a good June day yields only ≈420 Wh from a 300 W array — the
margin for consecutive cloudy days lives in your battery, not your panel. If the property is used
intermittently, size the battery for the gap between visits (150–200 Ah for ~5 days), or accept winter
power-down and remote-cycle the router (Teltonika RMS / RouterOS scheduler).
DC-run option (instead of solar at S1). You can keep the radio at the mast and feed the run from
the container's 12 V system: a DC-DC boost (12→24 V, A$20–40 est.) can drive the RUTX11's passive
PoE. Engineering guidance, not a sourced claim: over 230 m a naive low-voltage run loses too much voltage
in the cable — plan on the PoE extender / fibre / local-solar options rather than an unboosted direct
feed, and confirm the final volt-drop with the vendor before buying. (Also remember to fit the Ethernet
surge protector at the container end.)
9nbn fixed wireless — check it first anyway
The honest correction: v2 called the nbn Sheffield East tower “clear from ground level”.
From the true container, every nearby nbn fixed-wireless tower is geometrically
blocked or deep into diffraction. From the container at a 15 m mast:
Tower
Site
d km
brg°
clr@15 m
loss@15 dB
mast for bare ray
mast for full F1
7304008
Elizabeth Town 505 Dunorlan Road D
19.44
130.1
0.4
10.7
42.00
111.50
7305002
Sunnyside South 698 Sunnyside Road
8.11
101.8
2.8
24.6
85.75
148.25
7306013
Paradise 61 Hampson Lane SHEFFIELD
9.14
234.2
5.7
31.0
115.50
133.00
7306011
Sheffield East 88 Bridle Track Roa
2.67
179.1
7.3
33.1
118.00
132.00
From the true-container ranking (verdict_table.md §1);
clearances/losses at a 15 m mast, straight rays. These are nbn towers — informational only, because a
subscriber cannot mount an antenna on them and nbn installs its own equipment if the address
qualifies. Dunorlan (19.4 km, 10.7 dB) is the least-bad; the near ones are the worst — your own bowl
loves company.
Why check anyway? Because it is free, it takes three minutes, and it is the only path where
somebody else does the install and aims the antenna with their own tools and local knowledge. Our geometry
says expect a No; nbn's own design decides. And if Fixed Wireless says no, the same checker unlocks the
Sky Muster satellite path (§10).
Steps (owner-run — the checker is token-gated against automation)
Go to nbn.com.au/check (or an RSP's checker — same data).
Enter the street address exactly as on the utilities; for a new/unlisted lot use the
“missing address” enquiry form (photos + geocode help).
If it says Fixed Wireless: order any FW plan — nbn arranges the site visit and mounts/aims
the outdoor antenna and NTD (free standard installation for first-time FW connections).
If it says Satellite/Sky Muster instead: FW is out; §10 covers the satellite option.
Context (not a promise): third-party analysis shows the Sheffield town locality ~99%
Fixed Wireless (picknbn, Mar 2026), while some 7306 localities nearby are satellite-dominant —
so a No from the checker would not be surprising, and address-level is the only truth. Plans: budget FW
≈A$60–86/mo unlimited class (Dodo/Tangerine/Swoop listings); Telstra FW tiers up to
≈A$129/mo for the new fast tiers. nbn's “More Fixed Wireless” upgrade program is expanding
FW capability over time — worth rechecking in future years if it says no today.
10Other options & the law on boosters
The hard legal rule: consumer mobile repeaters/boosters are illegal to use in
Australia without written authorisation from the carrier(s) whose network you boost. ACMA's guidance is
unambiguous — even “exempt” class-licensed models still need the carrier's consent, and
unauthorised operation is an offence (detectable, penalised). And a repeater cannot fix a terrain-blocked
path: it amplifies whatever exists at its donor antenna; if your spot is shadowed, that is ~0 dB in,
~0 dB out.
What is legal without asking anyone: passive antennas and cabling (higher-gain panel/yagi, masts,
MIMO feeds, better coax) — ACMA regulates active amplification, not antennas; and a standard
carrier-approved device with a retail SIM. Carrier-approved hardware exists (e.g. Telstra's GO Repeater) but
is only an option if you commit to that carrier — verify written authorisation for the specific model
before purchase.
Installation standards (for a compliant build, not for licensing): mains wiring — AS/NZS 3000
(licensed electrician); mast/lightning — AS 1768:2021; PV array — AS/NZS 5033:2021. The big-mast
class should go to a professional with these in scope.
The full menu, ranked for your situation
nbn FW address check (§9) — free; do it first.
S1 15 m mast (§2/§6) — the strongest terrestrial path found on the block.
Container mast to Deloraine — graze-grade fallback; simplest to build.
Carrier 5G/4G home internet checks (Telstra 5G Home, Optus 5G Home) — address-gated on 5G
coverage; expect No at this address — the equivalent play is the BYO SIM + router plan above.
Sky Muster (nbn satellite) — works anywhere with a clear northern sky view; nbn-supplied
dish via an RSP; commonly free standard install; plans ≈A$60–100/mo; higher latency; better suited to
an occasionally-visited property than to real-time use.
Starlink — excluded by the owner on cost (from ≈A$75/mo; Mini kit A$289 as listed
Oct 2026). Noted so the menu is complete, not to reopen it.
11Field-test plan — the first weekend
Everything in this report is geometry. This plan converts it into measurements. Budget A$100–300,
one weekend, and it decides which (if any) of the builds above you pay for. Step 0 first: run the nbn
address check — if Fixed Wireless comes back, you may stop here.
Tools
SIMs: one prepaid per candidate — Telstra full-network (Boost gives it at prepaid prices),
Optus, and optionally a TPG/Vodafone set. Total ≈A$60–90.
Android apps:Network Cell Info Lite (RSRP/RSRQ/SINR + band + cell, live),
NetMonster (band/cell history), CellMapper (logs + uploads to the public tower map).
iPhone: Field Test (dial *3001#12345#*) → Serving Cell Info, plus a
speed-test app. (iPhone can't upload to CellMapper — use any borrowed Android for that step.)
Compass app; paper log (or the table below); the 50 m Cat6 patch + bracket/straps if you have them.
Where and when to test
Container bench (ground truth): all SIMs, ~10 minutes each, morning and late afternoon.
Raised test point: a 3–6 m temporary pole (safe) — or the tree at a low, accessible
height if you insist — same SIMs, same logs.
The S1 trial (the decision-maker): a temporary pole/mast at the SE tip —
−41.374465, 146.379847 (best cell −41.374375, 146.379727).
Aim ~63° ENE at the Sassafras pair, and also try 124° ESE at Deloraine, then sweep.
Bearing sweeps (container): Deloraine 124.6°; Sassafras pair 63–64°;
Railton 55.6° (blocked in theory — cheap to check); Elizabeth Town 110.8°;
Sheffield East 179° (reference only — a phone SIM cannot use an nbn tower); then a
full 360° sweep in ~30° steps to catch surprises (the ACCC inventory lists extra distant Telstra sites
toward ~40–62° NE and ~347° N).
Repeat on a wet day. If the wet/dry delta is large, the path is still foliage-dominated —
decision-critical information.
Log at every test point: carrier/SIM · phone · GPS pin (screenshot) · date/time
· weather (dry/wet) · position (bench / pole-top / bearing) · RSRP dBm ·
RSRQ dB · SINR dB · band (B28 etc.) · Cell ID (PCI/eNB) ·
camped-on-tower or searching? · SMS send test (3 attempts, count failures) · speed up/down if it
connects.
How to read the results (engineering judgement — calibrated to this survey's losses)
Finding (best bearing, raised point)
Interpretation
Action
RSRP ≥ −95 dBm, SINR ≥ +5, SMS ok
15 m class + panel will give usable service
Build the S1-area kit (§7) with the winning carrier
Short-pole kit may suffice — prefer nbn FW / engineered option; S1 is your best card
RSRP < −105 or SINR < 0 on all main bearings (124.6°, 63–64°, 55.6°)
Ground reality matches the “hard” case
Go nbn FW (if offered) / Sky Muster / get mast quotes; don't spend on 15 m gear
Best result on a bearing with no surveyed tower
Suspicious (reflection or unsurveyed site)
Log the Cell ID and confirm on CellMapper before believing it
The CellMapper trick (learn which tower your phone actually camps on): log with CellMapper on
Android, upload, then search the captured eNB ID on cellmapper.net and
read off which physical tower serves you, its band, and neighbours. This settles what coverage maps cannot:
e.g. “the phone is camping on Railton (700 MHz), not Elizabeth Town — that's why SMS only
works in the morning.”
After the test — the decision tree. (1) nbn FW offered? → order it, done.
(2) Best raised result on 63–64° from S1 with RSRP ≥ −95 / SINR ≥ +5 → build the
S1 15 m kit. (3) Marginal → S1 is still the best card; consider 25 m class or wait for nbn. (4) Nothing
better than −105 anywhere → satellite / authoritative quotes, not a spending spree. The single most
expensive mistake this plan prevents is buying a 15 m rig for a path that needs more — or buying anything
before the free checks.
12Method, data & limitations
What was computed. All geometry measured from the true container point
(−41.372605, 146.37865; ground 245.5 m; pinned after v2 from the owner's annotated map — three
independent readings agree within ~10 m). Towers: all 53 logged sites within 30 km (ACCC 2026 infrastructure
extracts + geocodes). Terrain: DEM (AWS terrain tiles, z14, ~2 m/px class at this latitude) along straight
rays; every profile evaluated for worst clearance and single knife-edge diffraction loss (ITU-R P.526-style),
worst case over the first Fresnel zone; a k=4/3 atmospheric-bending check for the top candidates. Masts:
tower transmit antenna assumed 25 m AGL (sensitivity: changing it to 15/35 m shifts modelled loss to
4.8/3.0 dB and the needed receive-mast values to 5.75/0.25 m on the Deloraine path — the conclusion
“near-graze” is robust). Property search: 372 non-road cells scored at 15 m and 25 m masts; eight
candidate spots (S1–S8) shortlisted and analysed in detail.
Boundary-alignment QA overlay — the Lot 1 polygon drawn over the basemap: the
provenance check that the cadastral boundary used in every map here matches the real block (south slopes
above the Railton–Rattler trail; Redwater Creek to the east; the emphasis marks and measure popup are
working artifacts of the mapping session).
Source: Crew 6 (supporting/overlay_final.png) — boundary QA for all maps.
Corrections timeline (why there are three editions)
v1: terrain maths bug (radians fed as degrees) — corridors ran wrong; superseded.
v2: maths fixed; anchor wrong — the OSM road-node geocode 1.1 km SSE (−41.38174,
146.38463; 1,132 m at 153.8°), on the far side of the container's own south crest. Verdicts internally
consistent, positionally wrong; superseded by this report.
v3 (this): true container point + whole-property search + 53-site re-ranking. A third
“provisional” anchor (raw listing geocode, 2.65 km SSW) appears only in the anchor-sensitivity
table to show how much a geocode choice moves verdicts.
Honest limitations (read before spending)
Geometry, not signal. No on-site measurement was made and the property was not visited by any
crew. A terrain calculation cannot know your local clutter, foliage, or noise floor. Treat every
“clear” as geometrically clear — confirm by field test.
Vegetation is not modelled. The rays assume bare terrain. Trees add loss (ITU-R P.833: ~0.17
dB/m at ~950 MHz in-leaf; ITU band 26.5–34 dB saturation) and can move the effective horizon. Clear the
mast's sightline of trees in the field-test stage.
DEM vertical error ±5–10 m over this terrain; tower positions/coordinates partly from
geocodes (rows flagged “APPROX COORDS” are indicative); tower heights assumed 25 m AGL.
Model band: for blocked/grazing paths, treat the dB figures as ±5–7 dB; the classes
(clear ≤6 dB / workable ≤12 dB / blocked >12 dB) are what matter, not the second decimal.
Not done / not knowable remotely: the official nbn address check (owner-run; token-gated);
local rigging quotes for the 15 m and 46–56 m mast classes; live RSP plan prices; anything requiring
a boot on the ground. Stated again: no measurements — that is what §11 is for.
Kit selftest (Crew 5): DEM profiles cross-checked against SRTM for 18 peaks — median
+2 m, best −1 m, max +18 m; regional sanity check on the massif (1,225 m peak at 11.0 km @ 221°,
within ~1 m of the independent prior survey). Data conventions: clearances signed metres (positive = clear);
bearings true north; distances geodesic km; coordinates WGS84. Everything above is traceable to the project
files in scratch/sheffield-net/ (verdict_table.md, placement.json,
anchor_sensitivity.md, property_dossier.json, solutions.md, sources.md, towers.json).
13Sources
Condensed from the project's sources.md (86 references) —
every number in this report traces to one of these. URLs are shown as text so this file stays fully offline.
A2 ShareTechnote — "LTE RACH" https://www.sharetechnote.com/html/RACH_LTE.html RACH procedure mechanics: preamble, power ramping, contention, Msg1–Msg4; why access stalls at coverage edge.
A3 CafeTele — Telecom Engineering Articles (incl. "4G LTE RACH") https://www.cafetele.com/articles.html Practitioner detail on RACH retries/power ramping at cell edge (article index; individual article pages under cafetele.com/articles/).
A4 MediaTek whitepaper — "5G NR Uplink Enhancements: Better Cell Coverage & User Experience" https://www.mediatek.com/hubfs/MediaTek%20Assets/Pdfs/White_Papers/UL-Enhancements-White-Paper-PDFULEWPA4.pdf Uplink is the cell-edge limiting factor; uplink-focused features (power control, repetition, bundling) exist because of it.
A5 Qualcomm whitepaper — "2023: Switched Uplink in 5G-NR — Benefits & Deployment Considerations" https://www.qualcomm.com/content/dam/qcomm-martech/dm-assets/documents/5G-Whitepaper-Switched_Uplink_in_5g_Benefits_and_Considerations-Qualcomm.pdf Industry framing of uplink coverage limits at cell edge.
A6 hIcellTek field guide (RSRP/RSRQ/SINR) https://hicelltek.com/en/blog/rsrp-rsrq-sinr-field-guide SINR→modulation/throughput mapping (throughput collapsing toward QPSK at SINR 0–5 dB); RSRP interpretation guidance.
A7 Intwine Connect — "Bars of Signal Strength" table https://intwineconnect.freshdesk.com/support/solutions/articles/33000223112-bars-of-signal-strength- Bars↔RSRP mapping used ("marginal" ≈ −113 dBm area for bottom 1–2 bars; 4–5 bars from −105/−90 up).
A8 MakeUseOf — finding best cell signal / reading signal in dBm https://www.makeuseof.com/how-to-find-best-cell-signal-home/ Field-test method basics and RSRP ranges (−120…−80 typical display).
A9 RFC 6298 (TCP RTO) https://www.rfc-editor.org/rfc/rfc6298 TCP *minimum* retransmission timeout ~1 s — why small-packet sends stall on packet loss at cell edge.
A10 TeleComponents coax reference (PDF, RG-58 attenuation tables) https://www.telecomponents.com/catalog/pdf/coax.pdf RG-58-class loss: already 34.8 dB/100 m @450 MHz → ≈45 dB/100 m class @700 MHz → ≈11 dB per 25 m (confirms prior doc's figure).
A11 ITU-R P.526 (diffraction theory; reference) https://www.itu.int/rec/R-REC-P.526/en Knife-edge/diffraction loss framework behind the survey's per-tower loss figures (6–12 dB grazing/shadowed cases).
A12 Solidsignal blog — "Mount a dish to the top of a tree" (wind effects) https://blog.solidsignal.com/tutorials/dont-mount-dish-top-tree Tree-mount sway: wind moves/aim-displaces top-of-tree mounts; why directional antennas on trees misbehave.
A13 Repeater-Builder — "Considerations for a Tree Suspended Vertical" https://repeater-builder.com/antenna/tree-antenna/tree-antenna.html Practitioners' engineering of tree-attached antennas: movement, revision work, reliability caveats.
B2 nbn blog — "A uniquely Australian problem: cockatoos vs infrastructure" https://www.nbnco.com.au/blog/the-nbn-project/a-uniquely-australian-problem-cockatoos-vs-infrastructure Same event, nbn's own account.
B3 Reuters — "Cockatoos cost Australian cable company" https://www.reuters.com/article/lifestyle/polly-want-a-broadband-connection-cockatoos-cost-australian-cable-company-idUSKBN1D309H/ Same; 80,000 AUD figure for damage at the time.
B4 BBC — "Australia cockatoos chew billion-dollar broadband" https://www.bbc.co.uk/news/world-australia-41857761 Same, international corroboration.
B5 ALDI Mobile — coverage & network statements https://aldimobile.com.au/pages/coverage "Uses the Telstra Wholesale Mobile Network… parts of Telstra's 4G and 3G" — the wholesale/full distinction vs Boost.
C1 Teltonika RUTX11 datasheet (via Digi-Key mirror) https://mm.digikey.com/Volume0/opasdata/d220001/medias/docus/8871/rutx11-datasheet.pdf Cat 6; 2× SMA mobile; Wi-Fi; RMS; ≤16 W max power.
C2 Teltonika wiki — RUTX11 Powering Options https://wiki.teltonika-networks.com/view/RUTX11_Powering_Options Passive PoE on LAN1, 9–50 VDC (Mode B); NOT 802.3af/at-compliant — active PoE will damage the device.
C3 Teltonika wiki — RUTX11 Supported Frequency Bands (page exists; band table requires interactive render) https://wiki.teltonika-networks.com/view/RUTX11_Supported_Frequency_Bands Reference for verifying the AU order-code band list (B28) at purchase.
C4 WISP Australia — RUTX11 product page https://wisp.net.au/teltonika-rutx11.html A$512.00 incl GST (indicative); AU stock.
C28 Bunnings — DETA earth rod https://www.bunnings.com.au/deta-earth-rod_p4430624 Earth rod ~A$16 (indicative); grounding build item.
C29 Standards Australia — AS 1768:2021 (lightning) and AS/NZS 5033:2021 (PV arrays) references https://www.standards.org.au Compliance standards cited in Sections 3 & 8.
D. Solar / power (Section 3.4)
D1 BOM climate averages — Launceston (Ti Tree Bend), station 091237 https://www.bom.gov.au/climate/averages/tables/cw_091237_All.shtml Mean daily solar exposure: June 5.4 MJ/m²/day (1.5 kWh/m²/day); December 24.8 MJ/m²/day (6.9 kWh/m²/day) — winter sizing basis.
D2 NREL PVWatts v8 API (used in earlier research for hourly/monthly PV estimates at −41.3817, 146.3846) https://developer.nrel.gov/docs/solar/pvwatts/v8/ Cross-check for PV yield modelling (methodology source; site-specific run used tilt 35°, az 180°, ~14% losses).
D3 StarPower Advance Solar Technology — 300 W fixed panel product page https://www.starpoweradvancesolartechnology.com.au/products/300w-12v-premium-fixed-solar-panel-mono-caravan-camping-rv 300 W rigid panel ≈A$150–250 class (indicative; listing captured Oct 2026).
D4 StarPower — 300 W folding kit listing (for comparison) https://www.starpoweradvancesolartechnology.com.au/products/atem-power-12v-300w-folding-solar-panel-kit-mono-shingled-etfe-caravan-camping-rv A$329.99 portable alternative (indicative).
E4 Dodo — internet plans (coverage site) http://coverage.dodo.com.au/internet/ Dodo FW $65.99/mth (50 Mbps class) then $85.99 (indicative).
E5 nbn — "Check address" https://nbn.com.au/checkhttps://www.nbnco.com.au/connect-home-or-business/check-your-address The official address checker (owner-run; token-gated against automation — could not be run by crew).
E6 nbn — More Fixed Wireless program + FAQs https://www.nbnco.com.au/residential/upgrades/more-fixed-wirelesshttps://www.nbnco.com.au/residential/upgrades/more-fixed-wireless/faqs FW upgrade program; new-connection kit = nbn outdoor antenna + connection box; free standard install; eligibility context.
E7 nbn — Fixed Wireless User Guide (PDF) https://nbnco.com.au/content/dam/nbn/documents/support/access-technologies-mtm/fixed-wireless/nbn-fixed-wireless-user-guide.pdf.coredownload.pdf "Your nbn Fixed Wireless equipment is comprised of… the nbn outdoor antenna and cable…" — what the install includes.
E8 nbn — Fixed Wireless Preparation Guide (PDF) https://nbnco.com.au/content/dam/nbn/documents/residential/upgrades/nbn-fixed-wireless-prep-guide.pdf.coredownload.pdf Install process/prep; professional siting of outdoor antenna.
E13 ALDI Mobile — plans/data-only + coverage pages https://aldimobile.com.au/pages/coveragehttps://aldimobile.com.au/collections/data-plans Telstra Wholesale network ("parts of Telstra's… network"); $2 starter SIM; data-only plans exist.
E14 Optus — 5G Home Internet plans page https://www.optus.com.au/internet/5g-home-internet "Special Price: 5G Home Internet from $54/month"; month-to-month; plans from $45/mth (6 months) promotions (indicative, Oct 2026).
E15 Optus — CIS, Plus 5G Internet plans (PDF) https://www.optus.com.au/cis/consumer/wireless-broadband/5g-home-internet/5g-home-broadband/cis_optus_plus_5g_internet_plans.pdf Plan structure/pricing terms (CIS).
E16 Telstra — 5G Home Internet https://www.telstra.com.au/internet/5g-home-internethttps://www.telstra.com.au/connected/internet/5g-internet-plans 5G Home Internet: 1000 GB/mth, Smart Modem 4, month-to-month, coverage-gated, modem return within 24 months if cancelled.
E17 TPG Telecom — media release, "TPG Telecom doubles mobile coverage as regional network sharing goes live" (30 Jan 2025, PDF) https://www.tpgtelecom.com.au/sites/default/files/media-release/Mediarelease_TPGTelecomdoublesmobilecoverage.pdf TPG↔Optus regional network sharing live → TPG SIMs can use Optus regional sites (Railton relevance).
E18 SkyMesh — Sky Muster® Plus plans page https://www.skymesh.net.au/nbn-services/sky-muster Satellite plan structure; "satellite internet without the setup headache" (install arrangements; plans ~$60–90 class — indicative).
E19 WhistleOut — IPSTAR (nbn satellite) provider page https://www.whistleout.com.au/Broadband/Providers/IPSTAR "3 plans from $60/mth to $100/mth" (indicative) — Sky Muster plan pricing anchor.
E20 Starlink AU (comparison only — excluded by owner) https://www.starlink.com/au Residential service from A$75/mo; service plans list; "no upfront hardware cost in select areas".
E21 JB Hi-Fi — Starlink Mini https://www.jbhifi.com.au/products/starlink-mini Starlink Mini kit A$289 (indicative, Oct 2026).
E22 Telstra — Mobile Broadband plans page https://telstra.com.au/internet/mobile-broadband Telstra mobile-broadband/data options context for BYO-SIM approach.
F. Legality (Section 8)
F1 ACMA — "Cellular mobile repeaters" https://www.acma.gov.au/cellular-mobile-repeaters Repeater rules hub; only authorised models may be used; authorisation process.
F2 ACMA — "Electrical products and devices" (jammers illegal; boosters illegal; "Mobile repeaters – you need permission") https://www.acma.gov.au/electrical-products-and-devices Written carrier permission requirement; penalties for unauthorised use; exempt-list context.
F3 ACMA — Cellular mobile telecom devices class licence https://www.acma.gov.au/cellular-mobile-telecom-devices-class-licence Class-licence framework for standard mobile devices (why your modem+passive antenna is fine).
F4 Telstra Exchange — "How to stay connected with antennas and repeaters" https://telstra.com.au/exchange/how-to-stay-connected-with-antennas-and-repeaters The carrier's own line: antennas/passive improvements OK; repeaters need authorisation.
F5 Telstra — GO Repeater (network coverage extension devices) + T&Cs PDF https://telstra.com.au/coverage-networks/network-coverage-extension-deviceshttps://telstra.com.au/content/dam/tcom/personal/consumer-advice/pdf/consumer/telstra-go-repeater.pdf Carrier-approved repeater option (Telstra-only) as the legal example.
F6 Standards Australia — AS 1768:2021; AS/NZS 5033:2021; AS/NZS 3000 (references) https://www.standards.org.au Lightning, PV-install and wiring standards cited for install compliance.
G. Field-test tooling (Section 9)
G1 Network Cell Info Lite (Google Play) https://play.google.com/store/apps/details?id=com.wilysis.cellinfolite App recommendation (RSRP/RSRQ/SINR, band, cell).
G3 CellMapper (Google Play + web map) https://play.google.com/store/apps/details?id=cellmapper.net.cellmapperhttps://www.cellmapper.net Logging/upload + the "which tower am I on" trick.
G4 MakeUseOf — cell signal guide (iPhone/Android field test methods) https://www.makeuseof.com/how-to-find-best-cell-signal-home/ iPhone Field Test (*3001#12345#*) and general measurement practice.